ZnLiFeO_3高温热敏厚膜材料的研究

ＺｎＬｉＦｅＯ３（ＺＬＦ）高温ＮＴＣ热敏厚膜材料，是以尖晶石结构的ＺｎＬｉＦｅＯ３导电陶瓷作厚膜浆料的导电相，以Ａｌ２Ｏ３瓷为基体，用厚膜工艺制成的。实验表明，在氮气中烧结的ＺＬＦ厚膜材料，室温方阻１０３Ω／□级，Ｂ值约１０００Ｋ。在高温５００～７００℃范围内，方阻降为１０２Ω／□级，Ｂ值仍小于１０００Ｋ。是一种很有前途的高温热敏材料。     

工艺参数对纳米颗粒Cu/SiO_2复合薄膜结构和光谱特性的影响

用离子束溅射法制备了具有反常光吸收特性的纳米颗粒CU／SiO2复合薄膜。获得了在离子来参数一定时，基片温度、膜料的沉积时间和镀膜后的保温时间等工艺参数对这种薄膜结构和光学特性的影响规律，并对纳米颗粒Cu／SiO2复合薄膜的反常光吸收特性作了计算和解释。     

垂直磁记录介质薄膜研制的新途径(英文)

本文阐述了铝氧化电沉积法获得磁记录材料的基本原理,研究了铝交流氧化膜中沉积磁性金属及其合金制备垂直磁记录薄膜的新途径,建立了铝交流氧化电沉积法,探讨了氧化膜的结构和磁特性的关系。     

L－B膜修饰电极循环伏安行为模拟──（Ⅰ）电荷转移速度常数对循环伏安性能的影响

本文用计算机数字模拟方法研究了电活性分子多层Ｚ型Ｌ－Ｂ膜修饰电极的循环伏安行为。计算了电极与修饰Ｌ－Ｂ膜分子第一层之间的电荷转移速度常数Ｋ_ｏ，Ｌ－Ｂ膜分子层间的电荷转移速度常数ｋ_ｉ；对峰电位差△Ｅ_ｐ及阳极峰面积Ｑ的影响，以及在不同条件下各层分子的氧化态分数随扫描时间的变化。为研究和设计电活性分子修饰电极的实际体系提供了大量数据和信息。     

微型真空力敏器件的研究

本文首次用电荷模拟法计算了真空微电子力敏传感器的场致发射阴极与阳极间的电场分布,同时计算了<100>晶向的方形硅薄膜受压形变与压力的关系,进而得出了这种传感器的电流-压力曲线.还做了水槽模拟电场分布的实验,理论与实验符合的很好.     

Grain Boundary Sliding in Fatigue of Pure Aluminum

The distributions of plastic strain near grain boundaries induced by fatigue loading were investigatedby the fiducial grid method in pure aluminum specimens, and the resulted grain boundary sliding(GBS) was systematically analysed. The results show that the strain field near a grain boundary isnonuniform. GBS is restricted by the junction of grain boundaries and causes discontinuities of bothdisplacement and strain. A peak value of shear strain was created in short-range area across the grainboundary. GBS plays an important role in cyclic softening and secondary hardening. The control fac-tor of GBS is the relative orientation between two grains and the macro orientation of the grainboundary rather than the ∑ value of the boundary.     

On slippage induced by surface diffusion

The mechanism of surface diffusion is taken at the basis of the phenomenon of slippage of the contact line of a liquid film. With the aid of the condition of continuity of the traction vectors at the solid-liquid interface, we obtained an evolution equation for the velocity of the fluid particles at the wall which shows a marked resemblance with Millikan's equation for the slippage coefficient of gases and reduces, in the limit of small surface diffusivity, to the classical Stokes-Einstein model. The influence of surface roughness is explicitely taken into account and, among other results, cases of absence of slip caused by the attachment of the liquid film to the solid surface and of slippage solely induced by surface roughness are found. Finally, the effect of the surface deformation upon the surface velocity of the fluid particles is examined in some detail.     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

水溶性防氧化剂在SMT用印制板上的应用

水溶性的防氧化剂是一种有机可焊性保护剂。其方法是在印制板完全阻焊、字符层的印刷，并经电检之后，通过表面浸渍在裸铜的贴片位或通孔内形成一种耐热性的有机可焊性膜层。这种有机、可焊、耐热的膜层，膜厚可达0.3-0.5mm，其分解的温度可达约300℃，传统的印制板的热风整平法亦无法满足QFP愈来愈密集的需求，同时也无法满足SMD表面平整度的要求，更无法适应PCB薄型化生产。烷基苯并咪唑的OSP法能弥补这项缺陷，因而在PCB业乃至SMT产业中得到了广泛的应用。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。